MAC 401 Dualuser manualTM
10 MAC 401 Dual™ user manualAttaching a cable to the male input connectorTo attach a power cable to the supplied input connector:1. Slide the bushing
Data link 11Data linkA data link is required in order to control a MAC 401 Dual™ via DMX.The MAC 401 Dual™ has 5-pin locking XLR connectors for DMX d
12 MAC 401 Dual™ user manualPhysical installationThe MAC 401 Dual™ can be placed on a horizontal surface such as a stage or clamped to a truss in any
Setup 13SetupWarning! Read “Safety Information” on page 3 before installing, powering, operating or servicing the MAC 401 Dual™.Control panel and men
14 MAC 401 Dual™ user manualLED indicatorsThe two LEDs on the right of the display indicate fixture status:• The DMX LED lights when the fixture is r
Setup 15DMXThe different pixel grouping, control mode and number of head modules fitted determine the number of DMX channels used:• Each pixel group
16 MAC 401 Dual™ user manualResetting via DMXBy default, it is possible to reset the whole fixture, reset pan and tilt only or reset effects only by
Effects 17EffectsThis section describes the lighting effects available in the MAC 401 Dual™.Shutter effectThe electronic ‘shutter’ effect provides in
18 MAC 401 Dual™ user manualPan and tiltThe MAC 401 Dual™ fixture’s moving head can be panned through 630° and tilted through 300°. Coarse (8-bit/Mos
Service and maintenance 19Service and maintenanceWarning! Read “Safety Information” on page 3 before servicing the MAC 401 Dual™.Warning! Disconnect
DimensionsAll dimensions are in millimeters©2009-20010 Martin Professional A/S. Information subject to change without notice. Martin Professional A/S
20 MAC 401 Dual™ user manualWarning! Disconnect from power and allow to cool before cleaning.To clean the fixture:1. Disconnect the fixture from powe
Service and maintenance 21Control menu service utilitiesFixture resetThe RST command in the MAN menu resets the fixture and can be used as a first re
22 MAC 401 Dual™ user manualFuse replacementWarning! Disconnect from power before replacing a fuse. Replace fuses with ones of the same type and rati
DMX protocol 23DMX protocolA range of protocols is available for the MAC 401 Dual™. The protocol used depends on how the fixture is configured. For i
24 MAC 401 Dual™ user manual—30 - 1920 - 3940 - 5960 - 7980 - 8485 - 8990 - 9495 - 99100 - 104105 - 109110 - 114115 - 119120 - 124125 - 129130 - 1341
DMX protocol 25—70 - 1920 - 3940 - 5960 - 7980 - 8485 - 8990 - 9495 - 99100 - 104105 - 109110 - 114115 - 119120 - 124125 - 129130 - 134135 - 139140 -
26 MAC 401 Dual™ user manual8160 - 910 - 1415 - 1920 - 2425 - 2930 - 3435 - 3940 - 4445 - 4950 - 5455 - 5960 - 6465 - 6970 - 7475 - 7980 - 8485 - 899
DMX protocol 279170 - 910 - 1415 - 1920 - 2425 - 2930 - 3435 - 3940 - 4445 - 4950 - 5455 - 5960 - 6465 - 6970 - 7475 - 7980 - 8485 - 8990 - 9495 - 99
28 MAC 401 Dual™ user manual1 If DMX Reset is disabled in the onboard control menus, a reset command can only be executed if channel 2 is set to DMX
DMX protocol 29LEE colors and their RGB equivalentsThe table below gives approximate RGB equivalents for the LEE colors available in the color wheel
Safety Information 3Safety InformationThe following symbols are used to identify important safety information on the product and in this manual:Warni
30 MAC 401 Dual™ user manualOnboard control menusSingle head module operationWhen only one module is installed on the head and the HEAD menu is set t
Onboard control menus 31INFOVERSMAINCPU firmware version in main processorHEADCPU firmware version in head processor front module / rear module (if i
32 MAC 401 Dual™ user manualDual head module operationWhen you install a second head module on the rear of the head and select DUAL in the HEAD menu,
Onboard control menus 33REAR MENUMANRSTReset fixture. Press [Enter] to confirmALL 0 – 255All LEDs, intensity 0 - 100%RED 0 – 255Red LEDs, intensity 0
INFOPTMPCURRDisplay current average pixel PCB temperatureMSRDisplay highest pixel PCB temperature since last resetMRDisplay highest pixel PCB temperat
Onboard control menus 35Adjustment submenuThis menu is accessed under ADJ in the SERV service menu. Adjustments are for service use only.FACTFACT LOA
36 MAC 401 Dual™ user manualTroubleshooting Problem Probable cause(s) RemedyFixture is completely dead.No power to fixture. Check power and connectio
SpecificationsPhysicalLength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ThermalCooling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Filtered forced air, temperature-regulated, low noiseMaximum am
4 MAC 401 Dual™ user manualPROTECTION FROM BURNS AND FIRE• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).• The ex
www.martin.com • Olof Palmes Allé 18 • 8200 Aarhus N • DenmarkTel: +45 8740 0000 • Fax +45 8740 0010
ContentsDimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 MAC 401 Dual™ user manualIntroductionThank you for selecting the MAC 401 Dual™, an intelligent lighting fixture from Martin Professional™. This LED
Introduction 7• Prepare the cabling and connectors for running the fixture off AC power as described in “Power cable and plugs” on page 9.
8 MAC 401 Dual™ user manualConnections panelFigure 1: Connections panel overviewABCDEFGA – AC mains power input(Neutrik PowerCon)B – Fuseholder, main
AC power 9AC powerWarning! Read “Safety Information” starting on page 3 before connecting the MAC 401 Dual™ to AC mains power.For protection from ele
Comments to this Manuals