Martin RoboColor III User Manual Page 1

RoboColor IIIuser manualP/N 35000050, Rev. B. © 1996 - 1999 Martin Professional A/S, Denmark

10 Setting Up RoboColor III SWITCHING ONHaving connected and addressed all units, you may now start operating thesefrom the lighting controller. The

User Manual Controllable Functions 11CONTROLLABLE FUNCTIONSThis section briefly describes the various functions that can be remotelycontrolled via the

12 Service and Maintenance RoboColor III SERVICE AND MAINTENANCE GENERAL MAINTENANCEWarning! Disconnect the system from AC power before removing any

User Manual Service and Maintenance 13 LAMP REPLACEMENTWarning! Disconnect the fixture from AC power before removing any cover. To reduce the risk of

14 Service and Maintenance RoboColor III Optimizing the lamp for maximum outputThe lamps are adjusted at the factory, however, fine adjustment of the

User Manual Service and Maintenance 15 VOLTAGE SETTINGSIt is essential that the voltage and frequency setting of your RoboColor III systemmatches the

16 Service and Maintenance RoboColor III 2 On the ballast, move the BLACK wire to the correct voltage terminal. Use thefollowing table to select the c

User Manual Service and Maintenance 17To replace the secondary fuse1 Access the circuit board as described earlier. 2 Replace the fuse with one of the

18 Service and Maintenance RoboColor III 3 Place the new CPU in the IC socket, ensuring that all pins enter the socketcorrectly, and that the CPU is c

User Manual DMX Protocol 19DMX PROTOCOLDMX channel Value FunctionMode 1 Mode 210 - 7475 - 138139 - 170171 - 202203 - 255Strobe, Stand-Alone, ResetNo f

2 Introduction RoboColor III INTRODUCTIONCongratulations on your choice of the RoboColor III system, designed andmanufactured by Martin Professional.

20 Stand-alone Sequences RoboColor III STAND-ALONE SEQUENCESThe following table provides a description of the stand-alone sequences selectablevia the

User Manual Troubleshooting 21TROUBLESHOOTINGProblem Probable cause(s) Suggested remedyNone of the RoboColor IIIs respond to the lighting controller.T

22 Troubleshooting RoboColor III No light emission from some or all RoboColor III heads.The lamp is on but the color wheel is on blackout position.Cha

User Manual Specifications 23SPECIFICATIONSELECTRICAL DATA (SYSTEM WITH 4 HEADS)• Power consumption: ...

0DUWLQ#3URIHVVLRQDO#$26Olof Palmes Allé 18 8200 Aarhus N Denmark Tel.: +45 8740 0000www.martin.dk

User Manual Setting Up 3SETTING UPThe RoboColor III system consists of the RoboColor III heads, which are thecolor changing spotlights, and the RoboCo

4 Setting Up RoboColor III Check voltage settingImportant! The voltage setting of the heads must match your local AC mains supply. The RoboColor III h

User Manual Setting Up 5Check voltage settingImportant! The controller’s voltage setting must match your local mains supply. The factory setting is pr

6 Setting Up RoboColor III Connect the lighting controllerOnce all heads have been connected to the RoboColor III controller, connect theRoboColor III

User Manual Setting Up 72 Connect the data output of the first RoboColor III controller to the data inputof the next device. Use the XLR-XLR cable sup

8 Setting Up RoboColor III ADDRESSING THE SYSTEMWhen using the RoboColor III with a lighting controller, you must set the DIP-switch to the start cha

User Manual Setting Up 9DIP-SWITCH TABLEThis table shows DIP-switch settings for channels 1- 511. To find a setting, locatethe channel in the table. F