Martin MAC 250+ User Manual

MAC 250 / MAC 250+user manual

10 MAC 250 and MAC 250+ Address and protocol selection The fixture address and oper

Control Panel11Demonstration program (dEMO)This menu offers a preprogrammed stand-alone demonstration. Before running the demo, set the minimum and ma

12 MAC 250 and MAC 250+ section 4OPERATIONThis section describes the effects and ho

Operation13current to trip circuit breakers. If sending “lamp on” commands to multiple fixtures, program a sequence that strikeslamps one at a time at

14 MAC 250 and MAC 250+ The MAC 250+ provides gobo indexing as well. Select the gob

Basic Service15section 5BASIC SERVICEThe MAC 250 and MAC 250+ operate under challenging conditions presented by heat, humidity, dust, and touring.Exce

16 MAC 250 and MAC 250+ Gobo orientationFigure 7 shows the correct orientation for

Basic Service17Configuring the optical system (MAC 250 only)Beam angle optionsThe standard MAC 250 lens system can be configured for 4 beam angles ran

18 MAC 250 and MAC 250+ Removing modulesColor/gobo/focus module1.Disconnect the fix

Basic Service19Replacing fusesPower supply fusesThe fuses for each of the 3 low-voltage power supplies are located on the printed circuit board. If on

section 1SafetySafety precautions ...

20 MAC 250 and MAC 250+ If the control panel does not work, boot mode can be engage

Appendixes21section 6APPENDIXESDMX protocol DMX1 DMX2 DMX3 DMX4Value Percent Function11If DMX Reset is disabled in the menu, a reset command can only

22 MAC 250 and MAC 250+ 4if gobo type = standard0 - 910 - 1920 - 2930 - 3940 - 4950

23 MAC 250 and MAC 250+ 60 - 255 0 - 100FocusInfinity Æ 2 meters7 0 - 1920 - 7980 -

Appendixes24Error messagesDisplay readout Appears if... What to doAUTO (Automatic protocol detec-tion error)Automatic protocol detection is enabled an

25 MAC 250 and MAC 250+ TroubleshootingProblem Probable cause(s) RemedyOne or more

Appendixes26PCB layoutHard bootjumperXLR jumperFanSwitchGobo wheelGoborotationColor wheelPrism flagPrismrotationDimmerFocusPanTiltHall sensorLinkLight

27 MAC 250 and MAC 250+ SpecificationsPhysical• Length...

← continuous ccw rotation continuous cw rotation→stGOBO ROTATIONINDEXED GOBO SELECTION0*1 2GOBO SHAKE G 845st→G 790 104→105 119G 6→120 134G 5→135 14

Safety3section 1SAFETYThank you for selecting the Martin MAC 250 or the MAC 250+. Both the MAC 250 and the MAC 250+ are yoke-mounted profile spotlight

Gradav Hire and Sales LtdThe Power HouseElstree Film StudiosShenley RoadBorehamwoodWD6 1JGPhone 020 8324 2100 FAX 020 8324 2933email [email protected]

4 MAC 250 and MAC 250+ section 2SETUPUnpackingThe MAC 250 and MAC 250+ come with:•

Setup5To install a lamp1.Remove the 2 Phillips screws from the lamp socket assembly. Pull the lamp and socket out of the head.2.Remove the old lamp, i

6 MAC 250 and MAC 250+ RiggingThe MAC 250 and MAC 250+ include a clamp mounting bra

Setup7Tips for building a serial link • Use shielded twisted-pair cable designed for RS-485 devices: standard microphone cable cannot transmit DMX dat

8 MAC 250 and MAC 250+ section 3CONTROL PANELYou set the fixture address, mode, and

Control Panel9Personality settings (PERS)Personality Path Options Effect (Default setting shaded, * indicates DMX override)Pan/tilt swapPATI/SWAPONMap