search

Martin M1 User Manual Page 10

  • Download
  • Add to my manuals
  • Print
  • Page
    / 16
  • Table of contents
  • BOOKMARKS
    • Rated. / 5. Based on customer reviews
Page view 9
8 © 2010 Martin Professional A/S
Guia de Segurança e Instalação Martin M1
Conexões de Alimentação
O Martin M1 tem especificação de 100 a 240 V 50/60 Hz, opera acima de 90 a 264 V 50/60
Hz. Não o conecte a alimentação fora desta faixa.
O cabo IEC fornecido não é instalado com um plugue específico do país.
Instale um plugue que atenda aos códigos elétricos locais e nacionais e seja adequado para os tipos
específicos de saída de energia do país.
Um plugue de aterramento de 3 pinos deve ser instalado seguindo as instruções do fabricante dele.
A tabela abaixo mostra alguns diagramas possíveis de identificação dos pinos. Se estes não
estiverem claramente identificados ou se houver dúvidas quanto à instalação apropriada, consulte um
eletricista qualificado.
Um cabo com um plugue NEMA 15-5P é fornecido para utilização do M1 nos EUA e no Canadá.
O cabo aprovado deverá ser utilizado na América do Norte.
Cor do fio (código UE padrão) Pino Símbolo
marrom ativo L
azul neutro N
amarelo/verde aterramento
1. Verifique se o interruptor de alimentação está na posição desligado (OFF).
2. Insira o cabo de alimentação fornecido no conector ENTRADA PRINCIPAL e conecte o cabo a
uma tomada de alimentação protegida e aterrada de modo apropriado.
3. Conecte o M1 alternando o interruptor de alimentação para ON.
Além da entrada IEC, o M1 também fornece uma porta de saída IEC para conectar a um monitor ou
a um dispositivo MaxModule.
Não exceda o consumo de tensão de 4A na porta de saída IEC.
8 © 2010 Martin Professional A/S
Martin M1 Safety and Installation Guide
Power Connections
Martin M1 is rated 100-240V 50/60Hz, operates over 90-264V 50/60Hz. Do not connect it to
power outside this range.
The provided IEC cable is not fitted with a country-specific plug.
Please install a plug that meets local and national electric codes and is suitable for the country's
specific power outlet types.
A 3-
prong grounding-type plug must be installed following the plug manufacturer’s instructions. The
table below shows some possible pin identification schemes; if the pins are not clearly identified, or if
you have any doubts about proper installation, consult a qualified electrician.
A cable with a NEMA 15-5P plug is provided for use of the M1 in the US and Canada. The approved
cable must be used in Nort
h America.
Wire color (standard EU code)
Symbol
brown
L
blue
N
yellow/green
1.
Check the Power Switch and ensure that is set to the OFF position.
2.
Insert the provided power cable into the MAINS IN connector and connect the cable to a properly
protected and grounded power outlet.
3.
Turn on the M1 by toggling the power switch to ON.
In addition to the IEC inlet the M1 also provides a IEC outlet port to connect a monitor or a
MaxModule device.
Do not exceed a current-draw of 4A on the IEC outlet port.
8 © 2010 Martin Professional A/S
Martin M1 Safety and Installation Guide
Power Connections
Martin M1 is rated 100-240V 50/60Hz, operates over 90-264V 50/60Hz. Do not connect it to
power outside this range.
The provided IEC cable is not fitted with a country-specific plug.
Please install a plug that meets local and national electric codes and is suitable for the country's
specific power outlet types.
A 3-
prong grounding-type plug must be installed following the plug manufacturer’s instructions. The
table below shows some possible pin identification schemes; if the pins are not clearly identified, or if
you have any doubts about proper installation, consult a qualified electrician.
A cable with a NEMA 15-5P plug is provided for use of the M1 in the US and Canada. The approved
cable must be used in Nort
h America.
Wire color (standard EU code)
Pin
Symbol
brown
live
L
blue
neutral
N
yellow/green
ground
1.
Check the Power Switch and ensure that is set to the OFF position.
2.
Insert the provided power cable into the MAINS IN connector and connect the cable to a properly
protected and grounded power outlet.
3.
Turn on the M1 by toggling the power switch to ON.
In addition to the IEC inlet the M1 also provides a IEC outlet port to connect a monitor or a
MaxModule device.
Do not exceed a current-draw of 4A
on the IEC outlet port.
8 © 2010 Martin Professional A/S
Martin M1 Safety and Installation Guide
Power Connections
Martin M1 is rated 100-240V 50/60Hz, operates over 90-264V 50/60Hz. Do not connect it to
power outside this range.
The provided IEC cable is not fitted with a country-specific plug.
Please install a plug that meets local and national electric codes and is suitable for the country's
specific power outlet types.
A 3-
prong grounding-type plug must be installed following the plug manufacturer’s instructions. The
table below shows some possible pin identification schemes; if the pins are not clearly identified, or if
you have any doubts about proper installation, consult a qualified electrician.
A cable with a NEMA 15-5P plug is provided for use of the M1 in the US and Canada. The approved
cable must be used in Nort
h America.
Wire color (standard EU code)
Symbol
brown
L
blue
N
yellow/green
1.
Check the Power Switch and ensure that is set to the OFF position.
2.
Insert the provided power cable into the MAINS IN connector and connect the cable to a properly
protected and grounded power outlet.
3.
Turn on the M1 by toggling the power switch to ON.
In addition to the IEC inlet the M1 also provides a IEC outlet port to connect a monitor or a
MaxModule device.
Do not exceed a current-draw of 4A on the IEC outlet port.
Page view 9
1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments
  • Wiley Tech air Aqua Stripper Spaun ProTemp
  • Electrolux Tumble dryers Apple Software StarTech.com Cable interface/gender adapters Pure Digital Radios Sharp Smartphones
  • LG VSF8405SC Clarke CBS1-5 Philips BM6W/10 Panasonic KX-TG6541 Philips 243V5LSB
  • Sony CCD-TRV59E User Manual Asus P8Z77-V LX2 User Manual Samsung 191T User Manual Ampeg PR-1832HE User Manual Moxa VPort 2141 Datasheet