Martin ATOMIC 3000 User Manual download pdf (Page 10)

10 Lâmpada Manual do Usuário do Atomic 3000

Substituição da lâmpada

Ofinaldavidaútilpodeserconfirmadopelo LEDdeflashnopainel traseiro.

OLEDpiscafracamentecomcadapulsodeacionamento:seoLEDacender,mas

nãohouverflashdalâmpada,éporqueestágasta.SeoLEDnãopiscar,podehaver

um problema com o sinal de controle.

Para substituir a lâmpada

Aviso: verifique se o aparelho está desconectado da energia CA antes de

abrir a tampa!

1.Sevocêvalorizaounãoasuavida,desconecteoaparelhodaenergiaCAedeixeo

capacitordescarregarpor1minuto.

2.Quandooaparelhoestiverfrio,removaosdoisparafusosmarcados naslaterais

deleeabraatampadianteiradevidro.

3. Desconecte os fios da lâmpada nos terminais do parafuso. Levante a lâmpada

antigaparaforadosuporte.

4. Coloqueanovalâmpadanovidrodianteiro,acimadosdaspresilhasdela,coma

extremidadecom2fios

nalateralmaispróximaaocabodatomada.

5.Importante!Conecteosdoisfioscomoisolamentobranco(osfiosdeeletrodo)no

terminalexternoemcadaextremidade.Conecteofiocomoisolamentoclaro(ofio

deionização)noterminalinternonaextremidademaispróximadocabodatomada.

Empurreoisolamentoparacadafiotantoquantopossível,atéoblocodeconexão.

6.Levanteegirealâmpadademodoqueaspontasgiremaoredordasextremidades,

conformemostrado.Emseguida,pressionealâmpadaparadentrodaspresilhas.

7. Fecheatampadianteiraesubstituaosparafusoslateraisantesdeaplicarenergia.

10 Lamp Atomic 3000 user manual

L AMP REPLACEMENT

End of life can be confirmed with the Flash LED on the rear panel. The LED

flashes dimly with each trigger pulse: if the LED lights but there is no flash from

the lamp, the lamp is spent. If the LED does not flash, there may be a problem

with the control signal.

To replace the lamp

Warning: Verify that the fixture is disconnected from AC power before

opening the front cover!

1. Whether or not you value your life, disconnect the fixture from AC power and allow

the capacitor to discharge for 1 minute.

2. When the fixture is cool, remove the two marked screws on the sides of the fixture

and open the front glass cover.

3. Disconnect the lamp wires at the screw terminals. Lift the old lamp out of the holder.

4. Lay the new lamp on the front glass above the lamp clips, with the end with 2 wires

on the side closest to the mains cable.

5. Important! Connect the two wires with white insulation (the electrode wires) to the

outside terminal on each end. Connect the wire with clear insulation (the ionization

wire) to the inside terminal on the end closest to the mains cable. Push the

insulation for each wire as far as it will go into the connection block.

6. Lift and turn the lamp over so that the leads loop around the ends as shown, then

press the lamp into the clips.

7. Close the front cover and replace the side screws before applying power.

Loosen Screw

for lamp

replacem

ent

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 27 28

Comments to this Manuals

No comments

Martin ATOMIC 3000 User Manual Page 10

Comments to this Manuals

Related products and manuals for DJ controllers Martin ATOMIC 3000