SynchroZap QX250User ManualP/N 35000025
10 SynchroZap QX250For independent control, each fixture must have its own address as in example 1. If inde-pendent control is not required, 2 or more
11Operationsection 3OPERATIONStand-alone operationThe SynchroZap QX250 may be operated without a controller in a stand-alone mode inwhich it performs
12 SynchroZap QX2503.Apply power to the SynchroZap. After it resets it is ready to respond tothe controller. The DMX protocol beginning on page 18 des
13OperationChannels 4 and 5: mirror drumsThe SynchroZap has 2 asymmetrically mounted mirror drums with independently controlla-ble rotation. Each drum
14 SynchroZap QX250section 4BASIC SERVICEReplacing the lampWARNINGThe lamp operates under high temperature and pressure and can explode. Always wear s
15Basic Service4.Wait for the lamp to reach full brightness. Position the fixture so the lightshines on a flat, white surface. 5.If there is an off-ce
16 SynchroZap QX250Adjusting EU model voltage settings 1. Disconnect the fixture from AC power and place it upside down on a worktable. If the lamp is
17Basic ServiceAdjusting US model voltage settings1. Disconnect the fixture from AC power and place it upside down on a worktable. If the lamp is hot,
18 SynchroZap QX250appendix a DMX 512 PROTOCOL6-channel DMX protocolChannel DMX Values Percent Effect10 - 1011 - 1920 - 3940 - 100101 - 109110 - 130
19DMX 512 Protocol30 - 89 - 1718 - 2627 - 3536 - 4445 - 5354 - 6263 - 7172 - 8081 - 8990 - 9899 - 107108 - 116117 - 125126 - 134135 - 143144 - 152153
© 1998, 1999 Martin Professional A/S, Denmark.All rights reserved. No part of this manual may bereproduced, in any form or by any means, withoutpermis
20 SynchroZap QX2501-channel DMX protocolChannel DMX Values Percent Effect10 - 5051 - 101102 - 152153 - 2550 - 1920 - 3940 - 5960 - 100Random sequen
21Specificationsappendix b SPECIFICATIONSMeasurements• Dimensions w/o bracket (LxWxH): ... 372 x 405 x 190 mm (14.6 x 15.9 x 7.5 in)• Weight w
22 SynchroZap QX250Construction• Housing...aluminum and steel
23DIP-Switch Tableappendix c DIP-SWITCH TABLEThis table shows DIP-switch settings for channels 1- 511. Note: Pin 10 is always OFF in the6-channel DMX
Martin Professional A/SOlof Palmes Allé 18DK-8200 Aarhus N, DenmarkPhone: +45 8740 0000 Fax: +45 8740 0010Internet: http://www.martin.dk#5#4#6#7#8#9
3Introductionsection 1INTRODUCTIONThank you for selecting the Martin SynchroZap QX250. This manual covers the Synchro-Zap QX250 with CPU software vers
4 SynchroZap QX250To protect yourself and others from burns and fire• Never attempt to bypass the thermostatic switch or fuses. Always replace defecti
5Setupsection 2SETUPThis section describes the steps required to prepare the SynchroZap for operation.UnpackingThe SynchroZap QX250 comes with:• 5-met
6 SynchroZap QX250WARNING!Disconnect the fixture from AC power before proceeding.The lamp operates under high temperature and pressure and can explode
7SetupCheck voltage and frequency settingsVerify that the settings printed on the S/N label match your local power supply. If the volt-age is not with
8 SynchroZap QX2501.Verify that the structure can support at least 10 times the weight of all installedfixtures, clamps, cables, auxiliary equipment,
9Setup1.Connect controller: For a DMX controller with 5-pin output, use a cable with a5-pin male and a 3-pin female connector, such as P/N 11820005. P
Comments to this Manuals